HVAC Tube Bender – Kink-Free Bends in Tight Spaces

$44.88 USD
Изчисляване на таксата за доставка при плащането
  • Worldwide shipping

  • Free returns

  • Carbon neutral

  • Secure payments

 
HVAC–RLEVER TYPESCALE 0–180°

Bend The Line Set Once. Bend It Right.

One lever, one forming wheel. The tube rolls around a formed radius instead of collapsing on one side — so the bore stays open and the refrigerant keeps moving.

Lever tube bender resting on a workshop bench

FIG. 01AT REST / BENCH

✓Kink-free bends on soft line sets
✓The same radius from the first bend to the last
✓Bends where the line set already is — no trip to the bench
✓Angle scale reads 0° to 180° with marks at 45, 90 and 135

Angle Readout

The Dial Tells You Where To Stop

Every bend has a target. The scale on the head runs from 0° to 180° and is marked at 45, 90 and 135, so you pull the lever to the angle you actually need instead of eyeballing it and bending again to fix it.

90°
 
 
 
0° 180°

0° · 45° · 90° · 135° · 180°
Needle shown at 45°

A bend that comes out at 60° when the run needs 45° is a bend you have to open up, close down, or replace. Reading the angle on the head removes that second guess from the job.

Procedure

Position. Clamp. Lever.

Three moves, in the order you already work. The lever only does one job: it rolls the tube instead of crushing it.

01

Position

Set the line set against the forming head at the point you want the bend to begin. The head defines the radius you are about to make.

02

Clamp

The base holds the run steady, so the bend happens exactly where you set it — not a hand-width further down the line.

03

Lever

Bring the handles together and roll the tube through the formed groove. Straight line in, clean radius out, bore untouched.

Why It Matters

A Pinched Bore Is A Callback

A line set does not need to be pretty. It needs to stay open. That is the whole difference between these two bends.

HAND BEND · ONE SIDE GIVES

 
 

The wall folds. The bore narrows.

Fingers push from one side and nothing supports the other. The tube flattens at the knee, the flow is restricted, and the fix is a new line set.

LEVER BEND · BOTH SIDES HELD

 

The wall rolls. The bore stays round.

The forming wheel carries the whole circumference around the radius, so the inside of the bend stays open and the system keeps its flow.

Key Features

What It Does On The Job

01

No Kinks, No Flattening

The forming wheel rolls the tube around the radius instead of collapsing one side, keeping the bore clear for correct refrigerant flow.

02

Consistent Radius Every Bend

The same groove geometry gives the same result from the first line set to the last, so a run stays even bend to bend.

03

Bends In Place

Made to be used where the line set already is — behind the unit, against a wall, up on a ladder. No pulling the run out to a bench.

04

Holds Its Alignment

No re-zeroing between jobs. The head stays where it was set, so the next bend starts from the same place as the last one.

05

Angle At A Glance

0° to 180° on the head, marked at 45, 90 and 135. You read the angle you have actually bent, not the one you hoped for.

06

Limited Lifetime Warranty

Backed for the life of the tool, on every install and retrofit after this one.

Two gloved hands rolling a line set through the lever bender

Specifications

The Readout

Type

Manual tube bender for HVAC-R

Function

Kink-free bending of soft line sets

Bending Method

Precision-formed grooves, roll-formed

Format

Handheld lever

Angle Scale

0° / 45° / 90° / 135° / 180°

Warranty

Limited lifetime

Best For

Air conditioning and refrigeration installs, repairs, retrofits

What Arrives

Box Open, Job Ready

Lever bender closed, resting on a bench
01

1 × Tube Bender

02

1 × Instructions

Take it out of the box, set it on the line, and make the bend. No setup step, no calibration before the first job.

Questions

Before You Bend

Q01

Will it work on the line sets I already run?

It is built for the soft line sets used on air conditioning and refrigeration work — the same runs you bend on installs, repairs and retrofits.

Q02

How do I know what angle I have bent?

The scale on the head runs 0° to 180° with marks at 45, 90 and 135. You bring the lever down until the reading matches the angle the run needs.

Q03

Can I bend the line set where it sits?

Yes. The lever is made to work in place — behind a unit, against a wall, in the spots where you cannot carry the whole run to a bench.

Q04

What stops the tube from sliding while I bend it?

The base clamps the run in place, so the bend starts at the point you set and stays there through the whole lever stroke.

Q05

Can I open a bend up if I went too far?

You can keep rolling it around the same head to take the angle further, or bring it back to the target. The radius stays where it was set.

Q06

What does the warranty cover?

Limited lifetime, for the life of the tool. Details sit in the instructions that ship in the box.

Straight Line In. Clean Radius Out.

One squeeze, one bend, one open bore. Keep the system flowing instead of coming back to a restriction you made yourself.

Lever Bender·0–180° Scale·Kink-Free Radius